Showing posts with label SR20. Show all posts
Showing posts with label SR20. Show all posts

Sunday, 4 December 2011

Alternator Woes

Recently the alternator has started playing up on my car.
So I bought a new S14 alternator thinking it would fit.
Turns out they are different.

Main differences between S13 SR20 and S14 SR20 alternator:
  • +ive post on the s13 is smaller (M6 thread as opposed to an M8 thread on the S14)
  • Upper mounting point on S13 is not threaded.
  • Different sized pulleys.
  • Wiring connector located on the opposite side of the alternator!


Conclusion:
You could make it fit with some alterations to the wiring and drilling out the upper mounting point but I rather get the right part. From my findings, it seems that the S14 and S15 alternators are the same however, so those are perfectly interchangable.

I then went and bought another one from a supplier that the local auto-electrician hooked me up with. The listing is for 180sx but it was wrong again, I'm not sure what this alternator was really for but it definitely is not for a RWD redtop SR20, I believe it was for a FWD Pulsar SSS SR20, the upper mounting point is different.

After this, I had researched that the alternator from the overseas model KA24 (240sx) would fit with a simple pulley swap and drilling out the threads of the top mounting points.
Ok - so a few weeks went by and my alternator finally arrived from the US.

Main differences between S13 SR20 and S13 KA24 alternator:

  • Upper mounting point on S13 is not threaded.
  • Different pulleys: KA24 is 4rib, S13 SR20 is 5rib.
So we are two up from the S14 SR20 alternator.
I then swap the pulleys over and find that the pulley sits 2mm out of alignment. The only way to correct this is to machine the back of the pulley down 2mm but risk the back of the pulley hitting the alternator housing.
I also find that when mounted, the KA24 alternator is larger and hits the intake manifold support bracket of the SR20, causing the belt adjustment's minimum/shortest setting to sit WAY before the adjuster itself bottoms out. Which means you'll need to run a longer belt or modify the support bracket to allow extra movement.
I didn't want to fuck around with machining pulleys and modifying the intake manifold support bracket so I just ordered a 2nd hand S13 SR20 alternator from the local wreckers.

So what I'm trying to say is that anyone who tells you (which is pretty much everyone on the US silvia forums) that the KA24 works with simple pulley change and boring out the top mount is rather wrong. The pulley definitely requires machining or you will running your alternator/water pump belt at a poor angle, something I definitely do not want.

Why didn't I get my alternator reco'd? Well the auto electrician wasn't able to source a lot of the rebuild parts for me (reg, diodes, etc).. apparently they don't make them any more for these types of alternators. Now that I think about it I'm actually quite sceptical about this and I really should have gotten a 2nd opinion.

What a fuck around.

Peace.

Friday, 26 August 2011

Leaking Water Pump



SR20 water pumps are not too bad of a job to do. Easily do-able at home with basic tools. 
A quick run down:
  1. Drain coolant
  2. Remove top hose (to allow shroud to be removed)
  3. Remove radiator fan shroud (from the top)
  4. Back off the clutch fan bolts (x4) but do not remove them
  5. Back off the alternator/waterpump belt
  6. Remove clutch fan and pulley
    [Steps 4-6 is done in this order so that you can undo the 4 clutch fan bolts while the pulley is held stationary by the belt/engine]
  7. Unbolt the water pump, give it a gentle tap with a rubber mallet or pry with screwdriver making sure not to score the mounting surfaces of the water pump. There will be a lot of coolant in there that comes rushing out so using a big tray underneath while you do this is a good idea.
  8. Remove as much coolant from block as you can, just soak it all up with rags.
  9. Raise the front of the car a bit more so that no coolant can seep out and interfere with the setting of the sealant
  10. Clean the mounting surfaces well, remove all old sealant with a razor, use some scotch brite and brake cleaner/grease wax remover. How well the new sealant sets and the longevity of the seal itself is dependant on how clean these surfaces are, this is not an area to skimp on.
  11. Transfer the studs of the old water pump to the new water pump
  12. Apply sealant to the mounting surfaces of the water pump and tighten bolts to torque specs. (IIRC I just did it with a 3/8 ratchet by feel, didn't have a torque wrench at the time but it is a good idea to do this and also do the bolts in sequence - from the inside to the outside). I used Permatex Ultra Grey and followed their directions, which was to mount the water pump finger tight and let it set for a while before applying full torque to the water pump bolts.
  13. Let the sealant fully set (time depends on sealant) before putting coolant back in.
  14. Remember to re-install the drain plug on the radiator.
  15. Refit water pump pulley and fan.
  16. Refit all belts
  17. Refit radiator shroud
  18. Refit top hose
  19. Undo the top radiator brackets and remove them
  20. Slip a large cut out of cardboard (or similar) to block air flow to the radiator while bleeding the cooling system (so that it can reach normal operating temperature thus opening the thermostat and cycling the cooling through for air bleed purposes)
  21. Fill coolant up to the top of radiator and run the engine
  22. No need to turn the heater on as there is always coolant running through the heater core on S chassis vehicles - don't run the fan as you'll be cooling the coolant
  23. Once the lower hose gets hot that means the thermostat has opened and coolant is circulating
  24. Undo the bleed bolt at the top hose to head junction until coolant comes out and reinstall
  25. Fill the radiator to the brim and close the cap
  26. Remember to remove the airflow blocking cardboard and reinstall the top radiator brackets
  27. Fill coolant reservior about 1cm above max
  28. Check for leaks
Trick here is to make sure the area is bone try and drop the rear end of the vehicle down or raise the front up so no coolant situates itself on the sealant while it sets. There is one little bleed screw on the top hose to the head junction for when you put the coolant in. I use Nissan genuine and wouldn't use anything else, its not expensive, and easy to get.. so why get anything else that may shorten the life of your water pump or offer compromised corrosion protection of your cooling system.
Take note, not all SR water pumps are the same. S13 black/red top run different water pumps to S14/S15!