Showing posts with label install. Show all posts
Showing posts with label install. Show all posts

Thursday, 5 January 2012

Autogauge Stepper Motor Series and Smoked Series Gauge Install and Review


From left to right: Oil temp, Oil pressure, Water temp.
The Oil temp gauge is an Autogauge Stepper Motor Series and the other two are Autogauge Smoked Series.
The Stepper Motor Series does the whole Defi start up ceremony where the needle does the full sweep and the lights flash upon start up. It also makes a loud, prolonged beep noise upon start up which can be a bit annoying. The Smoked Series are silent on start up.

Prior to fitting
The Stepper Motor Series oil temp gauge has a small white (2mm or 2.5mm allen) calibration screw at the back of the gauge. So before I installed the gauge to the car I checked the calibration by hooking it up to a spare car battery I have and placing the sensor in a pot of water. I boiled the water and adjusted the screw so that the gauge would read 100 degrees Celsius to ensure accuracy.
The Smoked Series do not have calibration screws, at least not exposed in its case - I have not opened them up to inspect internally.

The Install
First, I checked the combined current draw of all three gauges with a multimeter and found that it is around 0.3 - 0.4 amps. This was surprising as I was worried I'd have to split the wiring for the three gauges to spread the current draw to prevent exceeding the amperage rating of the 180sx's interior electrical circuits (eg cig lighter, audio unit, etc). I can't guarantee that this is the case for all after market gauges so check the current draw of your particular gauge!
With this knowledge, I tapped into the wires of the audio unit power supply: Permanent 12V (battery+ive), Accessory, and Illumination. And earthed it to the body. 
Automotive 8Pin connectors are your friend here:
Illustration from the Narva Website

What you have is three gauges, meaning three earth wires, three +ive, three sender wires etc etc.
You need to combine each category into one pin. Each pin of the Narva connector is rated at 20amps so its more than enough to handle the current draw of these gauges.


Note: the stepper motor series has a permanent 12V+ wire for peak recall memory so you'll need add that, if you are just installing the smoked series then the above diagram can be followed 100%.

This is the neatest way to install these gauges. Hard wiring them by soldering the wires into your existing electrical circuits means you need to cut the gauge out if you wanted replace them or remove them for whatever reason. Using connectors means you can replace each gauge (if one of them fucks out) efficiently and neatly - just like factory.

Senders
Im running a JAB design coolant neck sandwich plate (which is exactly the same as the Gktech coolant neck sandwich plate [I believe is a "JAB" design originally]) for the water temp sender and a Shadow Pro oil filter sandwich plate for the oil temp and pressure senders. Best thing for pressure senders is to isolate them from vibration - that means installing it OFF the engine (ie on the body somewhere) and use a braided oil line coming off the sandwich plate and onto the sender. This will prolong the life of your sender unit. 
Use thread sealant (I used Permatex thread sealant and it seems to work quite well) for all the sender threads.
Sandwich plate between head and coolant neck. (Easier to view if you download the image and zoom in)

Pressure sender mounted remotely. I still need to get a braided line 1/8NPT male and female fittings.

Completed Install:





Sunday, 4 December 2011

Alternator Woes

Recently the alternator has started playing up on my car.
So I bought a new S14 alternator thinking it would fit.
Turns out they are different.

Main differences between S13 SR20 and S14 SR20 alternator:
  • +ive post on the s13 is smaller (M6 thread as opposed to an M8 thread on the S14)
  • Upper mounting point on S13 is not threaded.
  • Different sized pulleys.
  • Wiring connector located on the opposite side of the alternator!


Conclusion:
You could make it fit with some alterations to the wiring and drilling out the upper mounting point but I rather get the right part. From my findings, it seems that the S14 and S15 alternators are the same however, so those are perfectly interchangable.

I then went and bought another one from a supplier that the local auto-electrician hooked me up with. The listing is for 180sx but it was wrong again, I'm not sure what this alternator was really for but it definitely is not for a RWD redtop SR20, I believe it was for a FWD Pulsar SSS SR20, the upper mounting point is different.

After this, I had researched that the alternator from the overseas model KA24 (240sx) would fit with a simple pulley swap and drilling out the threads of the top mounting points.
Ok - so a few weeks went by and my alternator finally arrived from the US.

Main differences between S13 SR20 and S13 KA24 alternator:

  • Upper mounting point on S13 is not threaded.
  • Different pulleys: KA24 is 4rib, S13 SR20 is 5rib.
So we are two up from the S14 SR20 alternator.
I then swap the pulleys over and find that the pulley sits 2mm out of alignment. The only way to correct this is to machine the back of the pulley down 2mm but risk the back of the pulley hitting the alternator housing.
I also find that when mounted, the KA24 alternator is larger and hits the intake manifold support bracket of the SR20, causing the belt adjustment's minimum/shortest setting to sit WAY before the adjuster itself bottoms out. Which means you'll need to run a longer belt or modify the support bracket to allow extra movement.
I didn't want to fuck around with machining pulleys and modifying the intake manifold support bracket so I just ordered a 2nd hand S13 SR20 alternator from the local wreckers.

So what I'm trying to say is that anyone who tells you (which is pretty much everyone on the US silvia forums) that the KA24 works with simple pulley change and boring out the top mount is rather wrong. The pulley definitely requires machining or you will running your alternator/water pump belt at a poor angle, something I definitely do not want.

Why didn't I get my alternator reco'd? Well the auto electrician wasn't able to source a lot of the rebuild parts for me (reg, diodes, etc).. apparently they don't make them any more for these types of alternators. Now that I think about it I'm actually quite sceptical about this and I really should have gotten a 2nd opinion.

What a fuck around.

Peace.

Monday, 29 August 2011

Ultra Racing Fender Braces - Full Review

Fitment:


Not an easy job. Fitting these took me about 7hrs altogether. This is not ultra racing's fault. But the fact that I had to fuck around with the big wiring harness underneath the wheel arch and short circuited the indicator circuit.... Also takes a few goes to line the door back up again.
The braces themselves are relatively high quality. The welds are decent, however the cuts on the end plate (the plate that is bolted to the fender frame) are rather sketch... as illustrated in this pic:


Ahh I was being a bit negative there.. The braces aren't something I'd want to be making myself, as there are some funky bends here and there and some tight bracket work to make them fit. And credit to the fabricators at ultra racing because they fit rather well. So for $160 posted to your door I'd save yourself the stress and just go and buy a pair. Fitment requires drilling of two holes for the end plates and also bend a small body extrusion from the car in this area:


Driving Impression:
 I hope it wasn't my head fucking with me because as soon as the moment my car twisted down my driveway it felt different. There was waayy less twist and it hopped off the gutter much more solidly.mGoing up my road and over familiar bumps the car felt bumpier, the front end generally stiffer.. This was fucking good and I hadn't even begin to hit the corners yet!

As I threw the car into various corners, S bends, off camber, on camber, etc the car showed more sign of oversteer than before. I'm entering corners on the overrun, 0% throttle, and the tail just tucks around the corners... like the optimum slip angle I'd like to think..haha. The front end just stays so planted, understeering is a thing of the past. I knew that S13's have flex issues especially in the front fender area but I can't believe how much of a difference these things make on an S13 chassis. Pretty sure these improvements are not psychological in proportion to the amount of time and effort I spent on fitment.. lol
I recommend this modification to anyone.
The results achieved from fitting these will differ depending on alignment settings, sway bars, spring rates, etc. So keep that in mind - you might not get increased oversteer like I did. The objective here is to achieve ANY difference because it means that there definitely is handling-altering-flex at the front quarter of the S13's.

The issues you'd come across is the location of the wiring harness under the RHS fender.. and the ride becomes a bit bumpier. You dont have to relocate the wiring harness but to get your car to any decent level of lowness subjects the harness to some high level of tyre rape. And you really don't want to be risking this because its a head fuck to fix if it fucks out. I just pulled mine over the fender brace, got rid of the thick conduit and used felt tape to insulate it so that the fender (standard fender) would still fit. Clearance is tight here. Sorry I don't have a photo of this.